Airlink101 AWLH6045 Manuel d'utilisateur

300N Draft 802.11n Wireless PCI Adapter Model # AWLH6045 User’s Manual Rev. 1.1

10 2.2 Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on

11 Step 3 Expand Network adapters from the list and verify that AirLink101 300N Wireless PCI Adapter is listed and no yellow question mark is beside

12 3. Configure the PCI Adapter This section describes how to connect your 300N Wireless PCI Adapter to a wireless network. Note to Windows XP Users

13 To open the PCI Adapter’s utility go to Start > (All) Programs > AirLink101 300N Wireless PCI Adapter > AirLink101 300N Wireless PCI Adapt

14 Step 2 If encryption is not enabled for the selected access point / router, skip to step 6. Otherwise, enter a Profile Name for your wireless setti

15 Step 4 Select the proper encryption setting for your wireless router or access point from the drop-down menu and click Next. Step 5 Follow the o

16 Step 7 Go to the Link Information tab and click on the More button. Step 8 Verify that you are receiving adequate Signal Strength and Link Quali

17 4. Configure the Wireless Utility This section describes the various functions of the Wireless Utility that you can configure, including the setti

18 The Wireless Information displays the current wireless network you are connected to as well as various other statuses such as the Signal Strength

19 4.2 AP List The AP List tab displays all the available Access Points detected by the PCI Adapter. Simply select the desired Access Point you wish

2 Table of Contents 1. Introduction ...

20 4.3 Configure Encryption Settings This section describes how to configure encryption settings for the PCI Adapter. Note: The encryption settings

21 Step 3 Verify the Network Name (SSID) is correct and click Next. For WEP Settings: WEP Step 4 Select the appropriate Authentication Mode and En

22 WEP Step 5 Select the appropriate Input Method, Key (password), Key Index, and click Next. WEP Step 6 Click Complete to finish the settings.

23 For WPA-PSK and WPA2-PSK Settings: WPA Step 4 Select WPA-PSK or WPA2-PSK and the appropriate Input Method and click Next. WPA Step 5 Enter the

24 WPA Step 6 Click Complete to finish the settings. Step 7 You should see a blue circle around the antenna icon indicating a valid connection. A

25 4.4 Profile Setting The Profile Setting tab lists all the profiles you have created. You can create new profiles for different network environment

26 Step 2 Enter a name for your new profile and click Next. Step 3 Enter the SSID (Network Name) of the wireless network you want to connect to and

27 Step 4 Configure any encryption setting if required and click Next. Step 5 Click Complete to finish the profile setting.

28 Step 6 Your new profile will be listed in the Profile List. Step 7 You can quickly select which profile you want to use from the Link Informatio

29 4.5 Static IP Setting To change the IP address of the wireless adapter to Static IP, follow the steps below: Step 1 On the last step of 4.4 Profi

3 1. Introduction Congratulations on your purchase of the 300N Draft 802.11n Wireless PCI Adapter. The 300N PCI Adapter provides wireless data rate o

30 4.6 About The About tab shows the Utility, Driver, and Firmware version as well as the MAC address of the 300N Wireless PCI Adapter.

31 Appendix A – Features Frequency Band • 2.4~2.5 GHz Standards • IEEE 802.11b / 802.11g • Draft 802.11n Interface • PCI Antenna type • 3 extern

32 Appendix B – Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limit

33 European Union Notice: Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC), the EMC Directive (89/336/EEC) and the L

34 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *

4 2. Installation 2.1 Install Driver & Utility This section provides instructions on how to install the 300N Draft 802.11n Wireless PCI Adapter.

5 Step 3 The Autorun screen will pop up. Select Install Driver and Utility from the menu. Note: If the Autorun screen doesn’t appear automatically

6 Step 5 Click Next to accept the default destination folder. Step 6 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Ye

7 Step 7 Verify Yes, I want to restart my computer now is selected and click Finish to restart your computer. Step 8 After the computer is restart

8 Step 9 Select Install the software automatically and click Next. Step 10 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, cli

9 Step 11 Click Finish. (Restart the computer for Windows 98SE and ME).