Wireless N 150 Router Model # AR570W User’s Manual Ver. 2A
11 Step 5 Power on the Router. It will take about 30 seconds. Step 6 Make sure POWER, WAN, WLAN, and the LAN port that the computer is connected to
12 Step 8 Verify the Internet Connection Type the wizard detected. If it is not correct, please configure it manually. Click Next. Note: If you are
13 Step 10 Please wait while the Wizard trying to connect to the Internet. If you see the window “Internet Connection Succeed”, your router has been
14 Step 11 Configure a name for your wireless network. Click Next. Step 12 Configure the security key for your wireless network. Check Enable WPA Pre
15 Step 13 Verify the settings you just configured for the Router. Click Finish to restart the Router. Congratulations! Your router configuration has
16 2.2 Connecting to the Router Wirelessly You must configure your wireless computer in order to establish a wireless connection to the router. In th
17 Step 3 Enter the Security key you configured for the Router (see Step 12 in Chapter 2.1). Click Connect. Step 4 Click on Close. Now the wireless
18 Chapter 3 Using Web Configuration Utility The Web Configuration Utility contains advanced features that allow you to configure the router to meet
19 Step 2 Enter your user name and password and click OK. (The default user name and password are both “admin”.) Step 3 When you see this page co
20 3.0 Setup Wizard Click on Setup Wizard and start the basic configuration for this router. If you have gone through the EZ Setup Wizard on the prov
Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B
21 Time Server Address Input the IP address / host name of time server here Daylight Savings If the country you live uses daylight saving, please
22 Primary DNS Please input the IP address of DNS server provided by your service provider. Secondary DNS Please input the IP address of another
23 Password Please input the password assigned by your Internet service provider here. DNS Address Select the type of how you obtain IP address f
24 PPTP PPTP requires two kinds of setting: WAN interface setting (setup IP address) and PPTP setting (PPTP user name and password). Here we start
25 Connection ID Please input the connection ID here, this is optional and you can leave it blank. MTU Please input the MTU value of y
26 Parameter Description User Name Please input user name assigned by your Internet service provider here. Password Please input the p
27 Password Please input the password assigned by Telstra. Assign login server manually Check this box to choose login server by yourself. Serve
28 2.4GHz (B): 2.4GHz band, only allows 802.11b wireless network client to connect to this router (maximum transfer rate 11Mbps). 2.4 GHz (N): 2.4GHz
29 WPA2(Mixed) Select WPA pre-shared key for Encryption. Enter the settings below: • WPA Unicast Cipher Suite: Select WPA2(Mixed) • Pre-Shared
30 If each field has valid numbers or IP addresses being assigned, the router is connected to the Internet.
Table of Contents FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT...2 TABLE OF CONTENTS ...
31 3.1 Network 3.1.1 WAN Use the WAN setting page to change your Internet connection type. The WAN setting page allows you to configure the Internet
32 ¾ LAN IP section Parameters Default Description IP address 192.168.2.1 This is the router’s LAN IP addre
33 ¾ DHCP Server section Parameters Description Lease Time Please choose a lease time (the duration that every computer can keep
34 If you want to delete a specific item, please check the “Select” box of a MAC address and IP address mapping, then click “Delete” button. If you w
35 Parameter Description Enable Static Routing Check/uncheck to disable/enable the NAT function. Destination LAN IP Enter the IP
36 Reset You can also click ‘Reset’ button unselect all. After you finish with all settings, please click “Apply” button. If you want to reset al
37 Provider Select a DDNS service provider. Domain name Your static domain name that use DDNS. Ac
38 3.2 Wireless 3.2.1 Basic Settings You can set parameters that are used for wireless clients to connect to this router. The parameters include SSID
39 SSID airlink101 This is the name of your wireless network. You can type any alphanumerical characters here, maximum 3
40 Parameters Default Description Encryption You can choose Disable, WEP, WPA pre-share key, WPA RADIUS for encryption mode. The detailed setti
3.5.1 Firewall ... 6
41 3.2.2.1 WEP Select “WEP” for the “Encryption” mode if you wish to use WEP to encrypt your wireless network. Parameters Description Key Len
42 change the encryption key frequently. So the encryption key is not easy to be broken by hackers. This can improve security very much. Select “WPA P
43 Parameters Description WPA Unicast Cipher Suite Please select a type of WPA cipher suite. Available options are: WPA (TKIP), WPA2 (AES)
44 Parameters Description Enable MAC Control Check/Uncheck to enable/disable wireless MAC control. MAC Address Input the MAC address of you
45 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the setti
46 RTS Threshold When the packet size is smaller than the RTS threshold, the wireless router will not use the RTS/CTS mechanism to send this
47 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the setti
48 Step 2 Push and hold the Easy Setup Button on the Adapter until you see the following window pops up on the computer monitor. Step 3 Within t
49 Parameters Description Enable WPS Check this box to enable WPS function, uncheck it to disable WPS. Wi-Fi Protected Setup Inf
50 Configure by Push Button Click “Start PBC” to start Push-Button style WPS setup procedure. This wireless router will wait for WPS reques
6 Chapter 1 Introduction Congratulations on your purchase of Airlink101 Wireless N 150 Router AR570W. This product is ideal for home or SOHO users wh
51 3.3 Application & Gaming 3.3.1 Virtual Server (Port Forwarding) The Virtual Server allows you to re-direct a particular range of service port
52 Public Port Input the port number of Internet IP address which will be redirected to the port number of local IP address defined above. Comment
53 Parameter Description Enable Special Applications Check to enable Special Applications, or uncheck to disable. IP Address This
54 From the Current Trigger-Port Table, you can select each Special Application setting by checking the “Select” checkbox. Parameter D
55 Parameter Description Enable DMZ Check/uncheck to enable/disable DMZ. Public IP You can select “Dynamic IP” or “Static IP” here. If
56 Reset You can also click ‘Reset’ button to unselect all. After you finish with all settings, please click “Apply” button. If you want to reset
57 There are many applications listed here. Please check the box of the special support for applications you need. After you finish with all settings,
58 Parameter Description Enable QoS Check this box to enable QoS, and uncheck this box to disable QoS. Total Download Bandwidth You
59 Parameter Description Rule Name Please give a name to this QoS rule (up to 15 alphanumerical characters). Bandwidth Set the ban
60 the limitation on all traffics from / to the specified IP address / port number), select “None”. Protocol Please select the protocol type of this
7 Back Panel Item Name Description Antenna The antenna is 3dBi dipole antenna. Radio ON/OFF Switch the button to activ
61 3.4 Access Restrictions This function allows you to configure some Internet access rules for your local computers based on the IP address, applica
62 Parameters Description Client PC Description Please input any text to describe this IP address, up to 16 alphanumerical characters. Client
63 Add When you finish with all settings, please click “Add” to save settings, you’ll be brought back to previous menu, and the rule you just set wil
64 Parameters Description Enable MAC Filtering Check this box to enable the MAC filtering function. Please select “Deny” or “Allow” to decide the
65 Parameter Description Enable URL Filtering Enable/Disable URL Blocking. URL/Keyword You can enter the full URL address of a we
66 3.5 Security 3.5.1 Firewall Excepting NAT, this router also provides firewall function to block malicious intruders from accessing your computers
67 3.5.2 DoS (Denial-of-Service) Denial of Service (DoS) is a common attack measure, by transmitting a great amount of data or request to your Intern
68 Parameter Description Ping of Death Set the threshold of when this DoS prevention mechanism will be activated. Please check the
69 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the setting
70 3.6 Administration The Administration page allows you to specify a time zone, to change the system password and to specify a remote management por
8 Reset / WPS Reset the router to factory default settings (clear all settings) or start security synchronization function (WPS). Press this button an
71 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the setti
72 After you finish with all settings, please click “Apply” button. If you want to reset all settings in this page, please click “Cancel” button. Aft
73 3.6.3 Remote Management You can manage this router remotely by enabling the ‘Remote Management’ function. Parameters Description Host Addres
74 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the settin
75 3.6.5 Configuration Settings The Configuration Settings screen allows you to save (Backup) the router’s current configuration setting. Saving the
76 3.6.6 Log All important system events and system security are logged. You can use this function to check the log of your router. Parameters D
77 3.6.7 Statistics View the statistics of packets sent and received on WAN, LAN and Wireless LAN. Click Refresh to display the latest information
78 3.7 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the Internet, LAN c
79 You can use this function to show the Wireless LAN status of your router, including ESSID (the name of your wireless network), Channel number, and
80 Chapter 4 Troubleshooting If you have trouble connecting to the Internet, try the following steps: Step 1 Power off the Cable/DSL modem, router,
9 Chapter 2 Installing the Router 2.1 Using EZ Setup Wizard Step 1 Insert the Setup CD into your CD-ROM drive. Step 2 Click Next to start the c
81 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Website: www.airlink101.com *Theo
10 Step 3 Connect one end of a network cable to the WAN port of the router and connect the other end to your DSL/Cable modem. Step 4 Connect one end
Commentaires sur ces manuels